The Pop-Up Effect: Why Buoyant Spheres Don’t Always Leap Out of the Water
News Release – LOGAN, UTAH, Nov. 2, 2016 – It’s a common swimming pool game: Force a buoyant ball underwater and let it go. The ball springs to the surface and jumps into the air. But, submerge the ball deeper underwater and the effect is often disappointing. Contrary to intuition, increasing the release depth often leads to a decreased pop-up height.
This simple fluid dynamics question has puzzled physicists for decades, but a new study published Nov. 1 in Physical Review Fluids, offers new perspective into the phenomenon and may clarify topics related to water exit dynamics and ocean engineering.
A team of researchers from Utah State University, Dartmouth College and Brigham Young University used high-speed imaging and particle image velocimetry to describe why buoyant spheres ascending through a fluid don’t always behave the way we expect them to.
“The pop-up height depends on the speed of the sphere at the point it breaches the free surface,” said lead investigator and assistant professor of mechanical engineering at USU, Tadd Truscott. “It doesn’t matter how deep the ball is when it’s released. There are a number of factors that affect its speed and trajectory until it reaches the surface.”
During ascent, wake and vortex structures often form around the sphere. Asymmetric vortex shedding and wake formations can alter a sphere’s upward movement and result in a non-linear trajectory. The authors demonstrate that rising spheres usually fall under one of two acceleration categories: 1) a vertical regime, or 2) an oscillatory regime.
“The vertical regime exhibits a nearly vertical underwater trajectory and results in the largest pop-up heights,” explains Brenden Epps, assistant professor of engineering at Dartmouth and co-author on the study. “The oscillatory regime exhibits a trajectory with periodic lateral motions and results in lower pop-up heights. Sometimes the ball may even breach the surface and skim across it rather than rising into the air.”
To test rising sphere behavior, researchers submerged stainless steel balls into a test tank at various depths and held them in place using a suction cup connected to a vacuum release mechanism. After sufficient wait time to allow the water to become quiescent, the suction cup released the sphere while four synchronized high-speed cameras recorded its ascent.
In total, 664 tests were performed using four balls of varying diameters and release depths. As expected, the maximum pop-up heights occurred when spheres were released from shallow depths; the lowest pop-up heights occurred when spheres were released from greater depths.
But the conversation doesn’t end there. Part of the pop-up height problem also depends on what happens to the sphere at the point of surface breach.
“Once the sphere clears the surface, the only force acting on it is gravity,” Truscott added. “So the pop-up height is determined by a transfer of kinetic energy to potential energy of the sphere after clearing the surface. However, the speed (and thus kinetic energy) of the sphere after it has cleared the surface is dictated both by the speed at which it approaches the surface (set by the underwater dynamics) and the change in speed during breach.”
The authors say their study has a broad range of applications. A better understanding of water exit dynamics, they explain, can be useful in maritime engineering and marine biology.
“Penguins exit the water after a hunt or to avoid predators,” they write. “It has been hypothesized that emperor penguins use bubbles released from their feathers during ascent in order to reduce drag and increase exit velocity and pop-up height. … Other important applications of the pop-up effect include underwater vehicle exit, floating sea structures and wave-energy converters.”
###Click here for Video and Photo Library
Dr. Tadd Truscott – USU College of Engineering | Dept. of Mechanical and Aerospace Engineering | firstname.lastname@example.org | office: +1-435-797-8246 | @TheSplashLab | splashlab.org
Dr. Brenden Epps – Dartmouth College | Thayer School of Engineering | office: +1-603-646-6656 | email@example.com
Matt Jensen – USU College of Engineering | firstname.lastname@example.org | office: +1-435-797-8170 | cell: +1-801-362-0830 | @EngineeringUSU | engineering.usu.edu